THE_COMPRESSOR 2 Manual
Thirteen compressor characters in one engine. Press SMART, play 8 seconds, and it sets itself up — then dive as deep as you dare.
Contents (9 chapters)
What It Is#
THE_COMPRESSOR 2 is a do-everything dynamics compressor with a split personality — in the best possible way. Under the hood is one configurable engine that can transform into thirteen curated Styles: aggressive FET drum-grab, slow smooth Opto, transformer-coloured bus glue, gentle tube Vari-Mu, transparent Clean Modern and Mastering, snappy VCA, and a brutal FET brickwall limiter. Pick a Style and the whole personality of the compressor — its detector, envelope, knee, timing and saturation — changes in one move.
But the real magic is that you never have to touch a Style. Hit SMART, tell it what you're working on (vocals, drums, bass, master…), play about 8 seconds of your track, and THE_COMPRESSOR 2 listens and writes its own settings: Style, threshold, ratio, attack, release, knee and makeup. It's a finished starting point in seconds, matched to your source.
And when you're ready to go deeper, three views unfold the engine on demand. Simple is four knobs and a glowing analog VU needle. Advanced opens a full pro surface with a live transfer curve, scrolling waveforms, a gain-reduction display and IN/OUT meters. Expert is a terminal-style list where every single parameter is editable inline. Same engine, same sound — just as much or as little control as you want, with all your settings preserved as you switch.
Why You'll Love It#
- SMART setup does the hard part. One button, about 8 seconds of playback, and the compressor configures itself for your source. No more guessing thresholds.
- MATCH gives you honest A/B. It level-matches the output peak to the input peak so "with compression vs. without" is a fair fight — no louder-sounds-better illusion.
- Thirteen characters, one plugin. From transparent clean leveling to iron-saturated bus glue to 20:1 brickwall limiting — all from a single engine.
- One-click VIBE moves. WARMER, TIGHTER, PUNCHIER, OPEN, HARDER — reshape the sound without hunting for knobs, in every view.
- Save and share characters. Dial in your own compressor character and save it as a user style (up to 20, shared across every DAW and project on your machine). Every character is also a short text code you can copy, paste and send to anyone — the code is the compressor.
- Draw your own curves. A proper editor for custom knee and envelope shapes — draw them, and they save and travel inside your styles and codes.
- Three views, zero relearning. Stay on four knobs forever, or open every parameter in Expert. Your settings travel with you.
- You can see the compression. Live transfer curve with a draggable threshold, scrolling input/output waveforms, a real-time gain-reduction ribbon and peak-hold meters. Great for working and learning.
- Built-in parallel compression. Mix, wet-only Makeup and post-mix Output are independent, so loudness and dry/wet never fight each other.
- Multiband when you need it. Switch on MULTIBAND and the compressor works on LOW, MID and HIGH separately, so a loud kick no longer pulls the vocal and cymbals down with it. Every Style keeps its character in every band, the main knobs still drive all three bands, and switching it off gives back the single-band compressor exactly.
- It goes as deep as the pros need. Side-chain HP/LP + weighting + external key + a sidechain listen button, LUFS-S and VU detection, hold, lookahead, stereo link, Mid/Side, and upward/bidirectional compression.
- Character on tap. Transformer / tube / FET / soft-clip / tape saturation with bias and GR-coupling, plus up to 8x oversampling for clean drive.
- Help built in. Tooltips in five languages (EN/DE/FR/ES/IT), the built-in manual, and an AI assistant.
The Interface at a Glance#
THE_COMPRESSOR 2 opens in a 900 × 560 px window with a vintage-console, dark theme; a corner handle lets you scale the whole interface. A thin top header carries a tooltip line on the left (it explains whatever you hover), the brand logo in the middle, and on the right Undo/Redo, AI Chat (robot), Docs (book), Settings (gear) and Bypass (power). Below it, a second row holds the SMART and VIBE pills on the left and the SIMPLE | ADVANCED | EXPERT view switcher on the right. Everything below is one big morphing display that changes with your chosen view:
- SIMPLE — a large analog VU needle showing live gain reduction, the STYLE pill, and four console knobs: IN TRIM, THRESHOLD, OUTPUT and MIX. A MATCH pill sits next to IN TRIM, and an SC pill under the meter switches to the external sidechain. While Multiband is on, a small MULTIBAND tag shows under the meter's left corner (the band controls themselves live in Advanced and Expert). Clean, fast, fun.
- ADVANCED — a live transfer curve with a draggable threshold line and knee handle, scrolling input/output waveforms, a gain-reduction ribbon with a GR readout, IN/OUT level meters, the STYLE pill, three knob groups — DYNAMICS (THRESHOLD, RATIO, KNEE, FLOOR), TIMING (ATTACK, HOLD, RELEASE, LOOKAHEAD, LINK) and OUTPUT (OUTPUT, MIX, IN TRIM, MAKEUP, plus the MATCH pill) — and four expandable panels along the bottom: SIDE CHAIN, CHARACTER, ROUTING and BANDS (one open at a time). While Multiband is on, a small light glows next to BANDS and the display shows the three bands.
- EXPERT — a terminal-style list of every parameter, editable inline, with IN / GR / OUT ASCII meters at the top and a CHARACTER / CODE block for copying, pasting and saving the character as a short text code. Drag a row sideways to scrub its value (Shift = fine, Cmd/Ctrl = coarse), scroll to step it, click a choice row to cycle it (right-click or Alt-click goes backwards), click an on/off row to toggle it. With Multiband on, the list adds the two crossovers, a BAND row (LOW / MID / HIGH) and that band's seven rows.
Knobs drag up and down; the value wells in the SIDE CHAIN, CHARACTER, ROUTING and BANDS panels drag sideways or up and down. Hold Shift as you press for fine control. In every view, double-click a knob, a well (or an Expert row) to reset it; right-click a knob or a well to type a value.
Other goodies: a Settings overlay (gear) with the language selector (EN/DE/FR/ES/IT), a Show Tooltips switch, a machine-wide Default View selector (LAST USED / SIMPLE / ADVANCED / EXPERT), Reset Zoom, a Tutorial link and your version number; the AI assistant panel; the built-in documentation; an update banner; undo/redo; and the corner zoom handle. Flip on Bypass and a full-window "BYPASSED - CLICK ANYWHERE TO RE-ENABLE PROCESSING" banner appears (in your chosen language).
Controls — In Depth#
Bypass (header power button)#
- What it does: Soft-bypasses the entire processing chain. While bypassed, a full-window banner appears; click anywhere on it to re-enable processing.
- Range/units: On/off (default: processing on).
- In your music: Instant A/B between processed and unprocessed signal.
- Pro tip: Pair it with MATCH for a fair comparison — same loudness in and out, so you judge tone and dynamics, not volume.
View switcher (SIMPLE / ADVANCED / EXPERT)#
- What it does: Switches the UI layout only. Settings are preserved across all three; only the surface changes.
- Range/units: 3 views. A new instance opens in Simple unless you've set a Default View in Settings; after that, each instance remembers the view you last used.
- In your music: A beginner stays on four knobs; a power user reaches every parameter — without touching the sound.
- Pro tip: Set up fast in Simple, then flip to Advanced to watch the transfer curve and confirm you're working the right part of the signal.
Style#
- What it does: Loads one of thirteen curated compressor characters in one move. A Style sets Ratio, Attack, Release, Knee width and Knee type, Detector, Weighting, Saturation type, Amount and Bias, ATK MOD, REL MOD and Oversampling (plus the Expert-only Envelope and Topology). It leaves your session alone: Threshold, In Trim, Makeup, Mix, Output, Hold, Auto Release, Floor, Direction, Lookahead, Link, Stereo mode, Coupling and the sidechain HP / LP / Source stay where you put them.
- Range/units: 13 factory Styles — Punch FET, Vintage Opto, Bus Glue, Tube Vari-Mu, Clean Modern, Mastering, Studio VCA, FET Brickwall, Classic Opto, Classic Bus, Pump, Vocal Ride, Transparent. A new instance starts on Clean Modern. Your own saved characters appear in a USER STYLES section below the factory styles (Simple and Advanced); the same dropdown also holds SAVE STYLE... and REMOVE STYLE.... In Expert, click the STYLE row to step through the factory Styles.
- In your music: One move to pick a personality — FET drum grab, slow opto smoothing, console-style bus glue, gentle vari-mu, transparent modern control, gentle mastering, hard-knee VCA grab, 20:1 brickwall limiting, a complete optical cell, console bus glue, gain that breathes with the beat, a voice ridden toward the threshold, or fast control with no color.
- Pro tip: Because Style leaves Threshold and your gain staging alone, you can audition them back-to-back without losing your levels. The music keeps going when you switch: you hear your dry signal at the level it was playing for a moment, then the compressor fades back in. If you've set your own oversampling factor, or in a session saved before 1.5.0, a switch takes a short mute instead. The moment you change any character setting away from the selected style, the display marks it —
Bus Glue*,MY STYLE*— so you always know whether you're hearing the character or your own variation (Threshold, trims, Makeup, Mix, Output, Hold, Coupling and the sidechain HP / LP / Source never trigger the marker; dial the value back or undo and it clears).
What each factory Style sets:
| Style | Ratio | Attack | Release | Knee | Detector | Saturation | Oversampling |
|---|---|---|---|---|---|---|---|
| Punch FET | 4:1 | 0.02 ms | 200 ms | Soft, 6 dB | Peak | FET 15 % | 2x |
| Vintage Opto | 3:1 | 10 ms | 60 ms | Soft, 8 dB | RMS | Tube 10 % | 2x |
| Bus Glue | 4:1 | 1 ms | 100 ms | Soft, 4 dB | RMS + Console weighting | Transformer 5 % | 2x |
| Tube Vari-Mu | 2:1 | 3 ms | 250 ms | Soft, 10 dB | RMS | Tube 12 % | 2x |
| Clean Modern | 4:1 | 1 ms | 100 ms | Adaptive, 6 dB | Hybrid | None | 2x |
| Mastering | 2:1 | 3 ms | 150 ms | Adaptive, 6 dB | Hybrid | None | 2x |
| Studio VCA | 4:1 | 1 ms | 80 ms | Hard, 0 dB | RMS | None | 2x |
| FET Brickwall | 20:1 | 0.05 ms | 50 ms | Hard, 0 dB | Peak | FET 25 % | 2x |
| Classic Opto | Comp | built in | built in | built in | Cell | Output tube | 2x |
| Classic Bus | 4:1 | 30 ms | Auto | built in | Cell | None | 2x |
| Pump | 4:1 | 10 ms | 150 ms | Hard | Peak | None | 2x |
| Vocal Ride | none | 10 ms | 150 ms | built in | Cell | None | 2x |
| Transparent | 4:1 | 1.2 ms | 90 ms | Soft, 24 dB | Peak | None | 2x |
User Styles & Character Codes#
- What it does: Saves the compressor's character — everything a Style sets, including any drawn knee or envelope curve — as a reusable user style, and encodes that same character as a short text code like
TC2-PECN-14H7-K5W6-F33Y-.... Loading a user style or a code swaps the personality exactly like picking a factory Style: Threshold, trims, Makeup, Mix, Output and your sidechain filters and routing stay put. - Where: Save from the STYLE dropdown (SAVE STYLE... opens a name prompt) or with [ SAVE ] in the Expert view's CHARACTER / CODE block (type the name right there; Enter saves, Esc cancels). Delete one with REMOVE STYLE... in the STYLE dropdown. In Expert, [ COPY ] puts the current code on the clipboard and [ PASTE ] reads one back — an inline question (for example "LOAD CODE K7Q4? KEEPS SETTINGS - SWAPS CHARACTER") waits for [Y]ES (Y or Enter) or [N]O (N, Esc or a click anywhere else) before anything changes. A pasted character shows as "CODE" plus its first four characters on the STYLE display until you save it under a name. The CODE line always tracks the live engine, so after any tweak the string on screen is the one to share.
- Range/units: Up to 20 user-style slots, stored per machine (every DAW and project sees the same list; saving under an existing name overwrites that slot). Names can be up to 18 characters — letters, numbers, spaces, hyphens and underscores, stored in capitals; save without a name in Expert and the slot is named "USER" plus the first four code characters. Codes are typo-proof — case, hyphens, spaces and line breaks don't matter, lookalike characters (O/0, I/L/1) are accepted, and a built-in checksum turns a real typo into
INVALID CODEinstead of a wrong compressor. - In your music: Build your signature bus-glue or vocal character once, then recall it anywhere — or paste a friend's code and hear their exact character on your source.
- Pro tip: A character with a drawn knee or envelope produces a longer code that embeds the curve's control points, so custom shapes travel too — paste it and the exact curves come back.
Threshold#
- What it does: Sets the level above which gain reduction begins (or below which upward gain begins when Direction is Upward or Both). It's on the THRESHOLD knob in Simple and Advanced, the threshold line on the Advanced display, and the THRESHOLD row in Expert.
- Range/units: −60 dB to 0 dB; a new instance starts at −6 dB (double-clicking the knob resets it to −18 dB).
- In your music: Pull it down to compress more of the signal; raise it to catch only peaks.
- Pro tip: In Advanced, drag the threshold line directly on the display — fastest way to dial it in by eye and ear.
Ratio#
- What it does: How strongly the level is changed past the threshold. Above 1:1 it compresses; below 1:1 it expands instead (with Direction on Downward it lifts the signal above the threshold, with Upward it pushes quiet signal further down, gate-style). Found in Advanced (DYNAMICS) and Expert; in Simple the Style sets it.
- Range/units: 1:10 to 100:1; 4:1 on a new instance. 1:1 = no change, 4:1 = moderate, 20:1 = limiting; from 90:1 up, the ratio blends into a true ∞:1 brickwall at 100:1. Below 1:1 the lift above the threshold stops at +24 dB.
- In your music: Low ratios for transparent leveling/glue; high ratios toward 20:1 for limiting and control.
- Pro tip: For glue on a bus, keep ratio low (around 2:1) and let just 1–3 dB of reduction do the cohesion.
Attack#
- What it does: How fast gain reduction engages once the signal crosses threshold.
- Range/units: 0.005 ms to 250 ms; default 1 ms.
- In your music: Short = grabs/tames transients harder; long = lets transients punch through.
- Pro tip: On drums, a slightly slower attack lets the initial transient snap past before the compressor clamps — more punch, not less.
Hold#
- What it does: Holds the gain reduction at its peak for a moment before the release starts. HOLD knob in the Advanced TIMING group; HOLD row in Expert.
- Range/units: 0 ms to 500 ms; default 0 ms (off).
- In your music: Keeps the compressor clamped through the body of a hit or note before it lets go — firmer, more controlled sustain.
- Pro tip: Hold plus a faster release shapes the body of a drum hit without smearing into the next one — the PUNCHIER vibe does exactly that with 50 ms of Hold.
Release#
- What it does: How fast gain reduction recovers once the signal drops below threshold. While Auto Release is on, the knob is dimmed and ignored.
- Range/units: 2.5 ms to 10 s; default 100 ms.
- In your music: Fast = energetic/pumping; slow = smooth/transparent.
- Pro tip: Tune release to the tempo — let the needle return to rest just before the next hit for a groovy, breathing pump.
Auto Release#
- What it does: Swaps the release stage for a program-dependent dual-envelope detector — a fast envelope (50 ms) tracks transients, a slow one (500 ms) tracks sustained material, and the louder of the two governs release. Overrides the Release knob. Switch it with the AUTO pill on the RELEASE knob (Advanced) or the AUTO RELEASE row (Expert).
- Range/units: On/off; default off.
- In your music: Hands-off, musical release for sources with shifting dynamics — vocals, drum bus, full mixes.
- Pro tip: Switch it on whenever a single release setting can't satisfy both the quiet and loud parts of a performance.
Knee width (KNEE)#
- What it does: Width of the soft transition around threshold over which the ratio ramps in. It applies to every knee type: at 0 dB you get a sharp corner whatever type is selected. With Adaptive it's the starting width that widens on dynamic material; with Custom it's the span your drawn curve covers. KNEE mini knob in the Advanced DYNAMICS group; KNEE WIDTH (BASE) row in Expert.
- Range/units: 0 dB to 72 dB; a new instance starts at 6 dB (double-clicking the knob resets it to 4 dB).
- In your music: 0 dB = hard, abrupt onset; larger = gentler, smoother.
- Pro tip: In Advanced, drag the small triangle handle on the transfer curve sideways to set the width by eye. Widen the knee for transparent vocal/bus leveling; narrow it for snappy, obvious drum control.
Knee type (KNEE TYPE)#
- What it does: Shape of the knee. Hard and Soft both follow the KNEE width you set (turn KNEE to 0 dB for a truly sharp corner); Adaptive widens the knee automatically on dynamic, peaky material — up to 2.5x the KNEE width — and stays at the KNEE width on already-dense material; Custom lets you draw the transition yourself. Choosing Custom reveals an explicit EDIT control — an EDIT pill under the KNEE TYPE selector (Advanced, CHARACTER panel) or an inline [EDIT] chip on the KNEE row (Expert) — that opens and closes the curve editor whenever you want; it never pops up on its own.
- Range/units: Hard / Soft / Adaptive / Custom; a new instance starts on Adaptive. Until you draw, Custom behaves like a hard knee.
- In your music: From surgical control to self-adjusting glue, or a fully custom transfer shape.
- Pro tip: In the CUSTOM KNEE editor, draw the curve across the knee width — drag points to move them, drag the line to bend it, double-click to add or remove points (up to 12), or start from the LINEAR / SOFT / GRAB presets. It opens over the plugin window and closes with its close button (top right), Escape, or switching the knee off Custom. Leave the knee on Adaptive for "set and forget" musicality; reach for Custom when you want a transfer curve nothing else can give you.
Range (RANGE)#
- What it does: Sets the most gain reduction the compressor may apply, however far the signal goes over the threshold. It sits next to KNEE. Not in sessions saved before 1.5.0, which stay on the older core.
- Range/units: 0 dB to 60 dB; default 60 dB.
- In your music: Keeps the body of a track while taming only what sticks out.
- Pro tip: The transfer curve shows the cap, so you can see where the reduction stops.
Envelope (Expert)#
- What it does: Chooses how the detector level is turned into gain-reduction movement, modelled on different circuit families: Linear RC (plain attack/release), FET Cell (release slows down the longer the signal sustains), Opto Cell (a fast stage plus a slow "memory" tail that lingers after loud passages), Bias Shift (vari-mu style — the harder it compresses, the slower it recovers), Custom (drawable, see below) and VCA (an extra-fast initial grab behind the attack). Only in Expert, on the ENVELOPE row; every Style picks its own.
- Range/units: Linear RC / FET Cell / Opto Cell / Bias Shift / Custom / VCA; a new instance starts on Linear RC. Auto Release, when on, replaces the envelope's own release behaviour.
- In your music: The difference between a compressor that snaps, one that breathes, and one that "remembers" the loud chorus.
- Pro tip: Keep a Style's settings but swap only the envelope to hear how much of a compressor's personality lives in its timing behaviour.
Custom Envelope (Expert)#
- What it does: In the Expert view, setting ENVELOPE to Custom reveals its own [EDIT] chip, opening the CUSTOM ENVELOPE editor that remaps the smoothed detector level (−60…0 dB in and out). Bend the diagonal to make the envelope lazy or grabby at different levels. Same gestures and LINEAR / SOFT / GRAB presets as the knee editor.
- Range/units: Drawable transfer curve; until you draw, Custom behaves exactly like Linear RC.
- In your music: Shape how the compressor rides different levels — gentler on quiet passages, grabbier on loud ones, or the reverse.
- Pro tip: Custom envelope characters save, share and restore like everything else — they ride along inside the user style and the character code.
Upward Floor (FLOOR)#
- What it does: Limits how much lift quiet material can get when Direction is Upward or Both. The upward boost grows as the signal falls below the threshold — but only down to FLOOR dB below it; anything quieter gets no extra lift beyond that point. The most boost you can get is roughly FLOOR × (1 − 1/ratio) — about 15 dB at the default 20 dB and 4:1. FLOOR mini knob in the Advanced DYNAMICS group; UPWARD FLOOR row in Expert.
- Range/units: 0 dB to 60 dB; default 20 dB.
- In your music: Stops upward compression from dragging room noise and hiss up without limit.
- Pro tip: If upward mode is pulling up hiss or bleed, lower the FLOOR to cap the boost; raise it when quiet passages need more lift.
Lookahead#
- What it does: Adds latency so the detector sees transients before processing them (reported to the host for delay compensation). LOOKAHEAD mini knob in the Advanced TIMING group.
- Range/units: 0 ms to 20 ms; default 0 ms.
- In your music: Catches peaks cleanly without softening the attack.
- Pro tip: A small amount (1–3 ms) is gold for transient-heavy limiting; keep it at 0 for tracking when latency matters.
Link (stereo link amount)#
- What it does: Stereo detection linking — 0 % = independent L/R, 100 % = fully linked (the loudest channel governs both); values in between blend. Ignored in Mid/Side, where Mid and Side always compress independently. LINK mini knob in the Advanced TIMING group; STEREO LINK row in Expert.
- Range/units: 0 % to 100 %; default 100 %.
- In your music: Lower preserves stereo movement; higher keeps a rock-solid centered image.
- Pro tip: On a wide stereo bus, back off slightly from 100 % to let the image breathe without the center wandering.
Input Trim (IN TRIM)#
- What it does: Pre-compressor gain — drive into the compressor. It's a knob in Simple, a mini knob in the Advanced OUTPUT group, and the INPUT TRIM row in Expert. MATCH writes it automatically.
- Range/units: −24 dB to +24 dB; default 0 dB.
- In your music: Push the compressor harder/softer without changing perceived output (compensate with Output).
- Pro tip: This is your "hit it harder" knob on character Styles — drive in, then pull Output down to taste.
Makeup#
- What it does: Wet-only gain applied after compression and saturation but before the dry/wet Mix; compensates for level lost on the wet path only. SMART and MATCH write this automatically. (Available in Advanced, as a mini knob in the OUTPUT group, and in Expert.)
- Range/units: −24 dB to +24 dB; default 0 dB.
- In your music: Restores wet-path loudness to match the dry signal — keeps parallel blends honest.
- Pro tip: Usually leave it where SMART/MATCH parked it; it's the key to a Mix knob that crossfades level and dynamics, not just volume.
Mix (Dry/Wet)#
- What it does: Crossfades between dry (uncompressed) and wet (compressed) signal.
- Range/units: 0 % to 100 % (0 % = dry, 100 % = fully compressed); default 100 %.
- In your music: Mid values give parallel / New York compression — punch with retained dynamics.
- Pro tip: Compress hard (low threshold, high ratio), then pull Mix down to ~30–50 % for thickness without crushing the life out of the source.
Output (Output Trim)#
- What it does: Final post-mix master output level; scales dry + wet together. In Simple this is the primary level control. SMART and MATCH park it at 0 dB.
- Range/units: −24 dB to +24 dB; default 0 dB.
- In your music: Set overall loudness without disturbing dry/wet balance or saturation character.
- Pro tip: Use Output for final gain-matching to the next plugin; use Makeup for the wet path alone.
SMART setup#
- What it does: Click SMART (available in every view) to open the SMART SETUP popup. Choose a SIGNAL TYPE, a COMPRESSION amount and an OUTPUT TARGET, then click LISTEN · 8 SEC and play your track. Step 1 listens to your input for 3 seconds; step 2 measures the compressed output for 4 seconds. SMART then picks the Style for your signal type, writes Attack, Release, Knee width, Ratio and Threshold, sets OUTPUT to 0 dB, and writes Makeup to hit your output target. Your MIX is held at 100 % while it measures and put back afterwards. The popup shows a summary (In … dB → Out … dB · Makeup … dB) and warns "Match capped at ±24 dB - lower IN TRIM" when the makeup would need more than ±24 dB. If it hears nothing, it says "COULDN'T HEAR ANY AUDIO" and lets you try again. One Undo reverts the whole SMART run.
- Range/units:
- SIGNAL TYPE: Vocals, Drums, Bass, Acoustic Gtr, Electric Gtr, Synth/Keys, Bus, Master, Speech, Custom (Bus is preselected). Style it picks: Vocals and Acoustic Gtr → Vintage Opto, Drums and Electric Gtr → Punch FET, Bass → Tube Vari-Mu, Synth/Keys → Studio VCA, Bus → Bus Glue, Master → Mastering, Speech → Clean Modern. Custom keeps your current Style, Attack, Release, Knee and Ratio and only sets Threshold and Makeup.
- COMPRESSION: 1–20 dB, from SOFT to EXTREME (5 dB preselected) — how much gain reduction SMART aims for on your peaks; more also raises the ratio and tightens the knee.
- OUTPUT TARGET: SAME (match the input peak, preselected), 0, −3, −6 or −12 dBFS. The fixed targets keep 1 dB of extra headroom.
- Attack and Release land within a range typical for the chosen source, so two runs can come out slightly different. The popup remembers your last choices.
- In your music: One-click, hands-off compressor setup matched to your source.
- Pro tip: Play your loudest, busiest part during LISTEN so the analysis sees real peaks — then tweak from a great starting point. You can click LISTEN first and then start playback: it waits up to about 10 seconds for audio to arrive.
- With Multiband: SMART never switches Multiband on. If it is already on, SMART sets the main controls as usual, and your band settings stay as they are on top.
MATCH (Simple + Advanced pill)#
- What it does: Two-step level match. Step 1 listens to your input for 3 seconds and sets IN TRIM so the compressor sees a healthy level (the body of the signal around −12 dBFS, peaks no hotter than −1 dBFS); step 2 measures the compressed output for 4 seconds and sets MAKEUP so the output peak matches the original input peak (net gain ≈ 0 dB). OUTPUT is parked at 0 dB; MIX is held at 100 % while measuring and then restored. The pill counts down while it listens. Cmd/Ctrl-click or Alt-click = level-only mode (adjusts MAKEUP only, leaves IN TRIM untouched).
- Where: Next to IN TRIM in Simple, and at the top right of the OUTPUT group in Advanced. In Expert, clicking the LEARN (AUTO-CLEARS) row runs the same match.
- Range/units: Momentary action. If no audio arrives, nothing is changed.
- In your music: Same loudness in, same loudness out — an honest, level-matched A/B against bypass.
- Pro tip: Run MATCH before you decide whether the compression is actually helping. Louder isn't better; matched is fair.
VIBE (one-click moves)#
- What it does: Click VIBE (available in every view) to open five one-click moves that reshape the current settings:
- WARMER — slower attack and release, a wider knee, more saturation drive and more Coupling.
- TIGHTER — faster attack and release, a higher ratio, a harder knee.
- PUNCHIER — attack set to 30 ms so transients escape, 50 ms of Hold, faster release, a bit more ratio and more REL MOD.
- OPEN — 50 ms attack, slower release, 2:1 ratio, 8 dB knee.
- HARDER — much faster attack, double the ratio, a hard knee, a touch more saturation drive, Hold off.
- Range/units: Momentary. Each move works on top of what's there, so clicking WARMER twice warms further; values always stay inside each control's range. Every click is one undo step.
- In your music: Quick, musical nudges without hunting for knobs — perfect in Simple, where Attack, Release and Ratio aren't on the panel.
- Pro tip: The saturation part of WARMER and HARDER only adds colour when a saturation type other than None is active — pick a Style with saturation (or set SAT TYPE) first.
SC HP (side-chain high-pass)#
- What it does: High-passes the detector signal only (audio path untouched). HP knob in the SIDE CHAIN panel; SC HIGHPASS row in Expert.
- Range/units: 20 Hz to 500 Hz; default 20 Hz.
- In your music: Stops bass from pumping the compressor.
- Pro tip: On a full mix or drum bus, set SC HP around 80–120 Hz so the kick stops dragging the whole mix down.
- With Multiband: SC HP, SC LP and Weighting rest while Multiband is on (they dim, and the SIDE CHAIN panel says why): each band's own range already decides what it listens to, and a side-chain high-pass would leave the LOW band unable to hear anything. They come back when you switch Multiband off.
SC LP (side-chain low-pass)#
- What it does: Low-passes the detector signal only. LP knob in the SIDE CHAIN panel; SC LOWPASS row in Expert.
- Range/units: 2 kHz to 20 kHz; default 20 kHz.
- In your music: Stops cymbals/hiss from triggering reduction.
- Pro tip: Roll it down if bright transients are causing the compressor to react more than the body of the sound warrants.
Weighting (side-chain pre-emphasis)#
- What it does: Applies an EQ curve to the detector only — None (flat), Console (takes the lows out of the detector below about 100 Hz — the bus-glue setting), Vocal (+6 dB presence lift around 3 kHz), Kick (+6 dB around 60 Hz). Custom currently behaves like None. WEIGHTING in the SIDE CHAIN panel; SC WEIGHTING row in Expert.
- Range/units: None / Console / Vocal / Kick / Custom; a new instance starts on None (Bus Glue switches it to Console).
- In your music: Tilts what the compressor listens to so it reacts to the right part of the spectrum.
- Pro tip: Use Vocal weighting to make the compressor follow the presence of a lead vocal rather than its lows.
Source (side-chain source)#
- What it does: Internal = reacts to its own input; External = reacts to the host's side-chain input, on every Style including the Feedback ones (falls back to internal if nothing is routed there). SOURCE in the SIDE CHAIN panel, SC SOURCE row in Expert — and in Simple, the SC pill under the meter does the same switch.
- Range/units: Internal / External; default Internal.
- In your music: Enables ducking one track from another (e.g., kick ducking a bass/pad).
- Pro tip: Route the kick to the side-chain input, set Source = External, and tune Release to the groove for classic pumping ducks.
Detector#
- What it does: Level-detection mode — Peak (transient-accurate), RMS (averaged loudness), Hybrid (a mix of both), LUFS-S (K-weighted loudness, about 400 ms averaging), VU (slow, about 300 ms averaging like a classic VU meter). DETECTOR in the SIDE CHAIN panel.
- Range/units: Peak / RMS / Hybrid / LUFS-S / VU; a new instance starts on Hybrid.
- In your music: Choose snappy transient response vs. smooth loudness-based or metering-style detection.
- Pro tip: RMS, LUFS-S or VU for transparent mastering-style leveling; Peak for catching fast transients on drums.
Sidechain Listen (headphone button)#
- What it does: The SIDECHAIN LISTEN headphone button in the open SIDE CHAIN panel replaces the output with the signal the detector hears — after SC HP/LP, Weighting and (with LUFS-S) the loudness filter — so you hear exactly what the compressor reacts to. Click again to return to normal.
- Range/units: On/off; always off when a session opens.
- In your music: Set the sidechain filters and Weighting by ear instead of by guesswork.
- Pro tip: Switch it off when you're done — while it's on you're not hearing your track.
Saturation (SAT TYPE)#
- What it does: Selects the saturation model in the character stage, applied to the compressed (wet) signal only, so Mix still blends against a clean dry. Each model has its own tone: Transformer (low-end bloom, softened top), Tube (warm lows, airy top, asymmetric warmth), FET (leaner bass, forward presence, the firmest clipping), Soft Clip (neutral, clean soft limiting), Tape (low-end bump, gentle top roll-off, the softest saturation curve). SAT TYPE in the CHARACTER panel; SATURATION row in Expert.
- Range/units: None / Transformer / Tube / FET / Soft Clip / Tape; a new instance starts on None.
- In your music: Adds colour — iron, tube glow, FET bite, clean soft limiting, tape softness, or none for transparency.
- Pro tip: Pick the model first with Amount low, then push Amount to find the sweet spot. The level is partly compensated, so more drive won't blow up your output — but it still gets a little louder, so use MATCH or Makeup when you compare.
Amount (saturation drive)#
- What it does: Drive into the chosen saturation model; 0 % bypasses the shaper. AMOUNT in the CHARACTER panel; the second SATURATION row (in %) in Expert.
- Range/units: 0 % to 100 %; a new instance starts at 0 % (double-clicking the knob resets it to 5 %).
- In your music: From subtle warmth to overt harmonic grit.
- Pro tip: A touch of Transformer + low Amount is the secret sauce on a bus — it "iron-glues" the mix together.
Bias (saturation asymmetry)#
- What it does: Pushes the shaper curve off-axis to favour even vs. odd harmonics (the offset is removed again, so no DC shift). BIAS in the CHARACTER panel; SAT BIAS row in Expert.
- Range/units: 0 % to 100 %; a new instance starts at 0 % (double-clicking the knob resets it to 10 %).
- In your music: More Bias = richer, tube-like even harmonics; less = cleaner, odd-harmonic edge.
- Pro tip: Nudge Bias up for vocal warmth; keep it low for a tighter, more transformer-style edge.
Coupling (saturation / GR coupling)#
- What it does: How strongly the current gain reduction pushes the saturation drive. COUPLING in the CHARACTER panel; SAT COUPLING row in Expert.
- Range/units: 0 % to 100 %; default 30 %.
- In your music: Couples character to dynamics — the shaper bites harder on louder material, like classic transformer iron.
- Pro tip: Raise Coupling so saturation blooms only on the hits — clean in the quiet parts, gritty on the peaks.
Oversampling (OVERSAMP)#
- What it does: Oversampling factor. It covers the whole compressor; in a session saved before 1.5.0, only the character/saturation stage. Whenever 2x or higher is selected, the oversampler stays in the path even with saturation on None, so the latency doesn't jump when you switch saturation on and off.
- Range/units: 1x / 2x / 4x / 8x; a new instance starts on 2x. Every Style sets it to 2x, so moving between Styles never changes the latency. A session saved before 1.5.0 keeps the 1x its older Style set. Choose 1x yourself when you need no added latency; picking a Style afterwards puts it back on 2x.
- In your music: Higher reduces aliasing from saturation at the cost of CPU and a small host-reported latency.
- Pro tip: Choose your Style first (it resets Oversampling), then bump to 4x or 8x on the master or when pushing heavy saturation.
ATK MOD (attack follows ratio)#
- What it does: Makes the attack faster as the ratio goes up — at 100 % and high ratios the attack drops to roughly a fifth of the knob setting, the classic "all-buttons" FET grab. ATK MOD in the CHARACTER panel; ATK-RATIO MOD row in Expert.
- Range/units: 0 % to 100 %; a new instance starts at 0 % (double-clicking the knob resets it to 20 %). Styles set their own (Punch FET 70 %, FET Brickwall 90 %).
- In your music: The harder you squeeze, the harder it grabs — aggressive control that tightens up automatically.
- Pro tip: Leave it at 0 % for surgical work where the attack must stay exactly where you set it.
REL MOD (release follows gain reduction)#
- What it does: Lengthens the release while the compressor is working hard — at 100 %, every 6 dB of gain reduction adds another full release time (6 dB ≈ twice as long). REL MOD in the CHARACTER panel; REL-GR MOD (STACKED) row in Expert.
- Range/units: 0 % to 100 %; a new instance starts at 0 % (double-clicking the knob resets it to 20 %). Styles set their own (Vintage Opto 70 %, Tube Vari-Mu 50 %).
- In your music: Light compression recovers fast, heavy compression recovers slowly — the smooth "memory" of classic opto and vari-mu boxes.
- Pro tip: Raise it on vocals and buses for smoother recovery after loud phrases; keep it low on drums where you want every hit to release the same way.
Stereo Mode (STEREO)#
- What it does: L/R = normal stereo compression; Mid/Side = the compressor works on Mid (center) and Side (stereo difference) as two independent channels, then decodes back to L/R. STEREO in the ROUTING panel; STEREO MODE row in Expert.
- Range/units: L/R / Mid/Side / Mid to Side / Side to Mid; default L/R. Mid to Side lets the center's level turn down only the sides; Side to Mid lets the sides' level turn down only the center. These two need the single-band compressor.
- In your music: In Mid/Side, a loud center (vocal, kick, bass) no longer pulls the stereo sides down with it — and busy sides don't duck the center.
- Pro tip: Try Mid/Side on a full mix when heavy center elements make the whole stereo image pump.
Direction#
- What it does: Downward = classic downward compression above threshold; Upward = boosts signals below threshold up toward it (capped by Upward Floor); Both = both at once. DIRECTION in the ROUTING panel.
- Range/units: Downward / Upward / Both; default Downward.
- In your music: Even out very dynamic material, or lift quiet passages instead of (or as well as) taming loud ones.
- Pro tip: Both with a sensible Upward Floor rescues uneven takes from both ends — quiet words come up, loud ones come down.
SC EQ#
- What it does: Six bands of EQ on what the compressor hears, never on the audio you hear. Each band is a Bell, Low Shelf, High Shelf, Low Cut, High Cut, Notch, Band Pass, Tilt Shelf, Flat Tilt or All Pass, with its own slope, and works on the stereo signal, or on only its mid or side part. The curve shows the real response; drag a band's number to move it, double-click it to switch it off.
- Range/units: 10 Hz to 30 kHz, -30 to +30 dB, Q 0.025 to 40, slopes from 6 dB/oct to Brickwall; all bands start off.
- In your music: Boost 200 Hz to make it ride the kick, or dip a resonance that keeps tripping it. Single band only; with Multiband on, each band is its own side-chain range.
- Pro tip: Use SIDECHAIN LISTEN to hear exactly what your EQ does to the detector.
Triggers (SOURCE: Host Sync, MIDI)#
- What it does: Host Sync generates pulses in time with your song: SYNC sets the note value, LENGTH how long the pulse lasts, OFFSET how often it comes, for dotted and triplet feels. MIDI makes held notes the trigger, with velocity setting how hard.
- Range/units: SYNC 1/1 to 1/16; LENGTH 0 to 100 %; OFFSET 50 to 200 %. In Host Sync, SYNC, LENGTH and OFFSET take the slots of HP, LP and WEIGHTING, which have nothing to filter.
- In your music: Sidechain-style pumping with no kick track needed. With the transport stopped, it keeps pulsing at the song's tempo.
- Pro tip: MIDI needs a VST3 or AAX host; the Audio Unit stays a plain effect, so your Logic sessions keep finding it.
Mid Link (ROUTING panel)#
- What it does: Moves the detector from the louder channel toward the center, and lets the sides keep their level while the center takes the reduction.
- Range/units: 0 % to 100 %; default 0 %.
- In your music: Glue a mix without narrowing it or letting a wide guitar duck the vocal.
LATENCY (ROUTING panel)#
- What it does: Reserves a fixed lookahead latency. LOOKAHEAD then moves freely up to that amount and your DAW never has to re-align.
- Range/units: Off, 1, 2, 5, 10, 20 ms; default Off, where latency follows LOOKAHEAD.
Auto Gain (ROUTING panel)#
- What it does: Sets makeup from your Threshold, Ratio and Attack: a share of the reduction a full-scale signal would get, smaller as the Attack gets slower. It adds to MAKEUP.
- Range/units: Off / On; default Off.
- In your music: Compare settings without the louder one winning. It comes from the settings, not the signal, so it never pumps.
- Pro tip: Trim the rest with MAKEUP or OUTPUT. Use MATCH when you want it measured from your actual track.
Auto Threshold (ROUTING panel)#
- What it does: Lets the Threshold work relative to the input's level. It follows peaks up at once and falls about 1.7 dB a second, so the same settings give the same reduction on a quiet track and a hot one.
- Range/units: Off / On; default Off. Below -40 dBFS it stops following. Classic Opto has no use for it, so it dims there.
- In your music: Keep one setting across takes or songs at different levels.
- Pro tip: With this on, a Threshold of -10 dB means 10 dB below the recent peaks.
Multiband (BANDS panel)#
- What it does: Splits the signal into three bands — LOW, MID and HIGH — and compresses each one on its own, then adds them back together. Switch it on with MULTIBAND at the top of the BANDS panel (the panel's header is the switch). The Style you picked runs in every band, with all its character: detector, envelope, knee, feedback, saturation. Saturation, Makeup, Mix and Output still act once, on the whole signal. MULTIBAND row in Expert.
- Range/units: Off / On; default Off. Off is the single-band compressor exactly as it always was. Switching it on or off keeps the music going: you hear your dry signal for a moment, then the compressor fades back in. In a session saved before 1.5.0 it fades the output down, switches while it is silent, and fades back up instead.
- In your music: One loud part of the spectrum no longer turns everything down. A big kick or bass note compresses the LOW band while the vocal, snare and cymbals keep their level.
- Pro tip: Start with the band controls at their defaults and only move the band that misbehaves. Most of the time one band (often LOW) needs its own threshold, and the rest can follow the main knobs.
Crossovers (LOW X / HIGH X)#
- What they do: Set where the bands meet. LOW X is the split between LOW and MID, HIGH X between MID and HIGH. On Min Phase the crossovers add no latency and, with nothing being compressed, sum back to a flat response. They stay at least 0.8 octave apart (sessions from before 1.5.0 keep the spacing they were saved with). A moved crossover glides to its new frequency instead of jumping. In the BANDS panel; X-LOW / X-HIGH rows in Expert.
- Range/units: LOW X 20 Hz to 1 kHz (default 150 Hz); HIGH X 1 kHz to 18 kHz (default 3 kHz).
- In your music: Put LOW X just above the kick and bass fundamentals, and HIGH X where the harshness or the air you want to control begins.
- Pro tip: On a mix bus, around 120 Hz and 4 kHz is a good start: LOW handles kick and bass, MID the body of the mix, HIGH the cymbals and sibilance.
Crossover (CROSSOVER)#
- What it does: Chooses how the bands are split. Min Phase adds no latency; the split shifts phase around the crossovers. Linear has no phase shift and adds 3072 samples at 48 kHz. Dynamic has no band split, so it's a true wire until it compresses, with no added latency.
- Range/units: Min Phase · Linear · Dynamic (default Min Phase).
- In your music: Min Phase for everyday mixing, Linear for mastering where the latency is compensated anyway, Dynamic when a track must stay untouched until a band actually needs compressing.
Band controls (THRESH, RATIO, ATTACK, RELEASE, GAIN, SOLO, BYPASS)#
- What they do: Each band has its own controls, set on top of the main knobs — so the main knobs still move all three bands. Pick the band with the LOW / MID / HIGH buttons (or click its lane in the display); the controls in the second row then edit that band:
- THRESH moves this band's threshold away from the main THRESHOLD (+ = compresses later, − = earlier).
- RATIO, ATTACK and RELEASE multiply the main values for this band (x2 at a 4:1 main ratio = 8:1).
- GAIN sets this band's level after its compression.
- SOLO lets you hear only the soloed band(s). BYPASS lets the band pass untouched — no compression and no band gain.
- In Expert, the BAND row picks the band, and its seven rows follow (LOW THRESH, LOW RATIO and so on).
- Range/units: THRESH −24 to +24 dB (default 0). RATIO, ATTACK, RELEASE x0.25 to x4 (default x1). GAIN −12 to +12 dB (default 0). SOLO and BYPASS on/off.
- In your music: Give the lows a slower release so bass notes don't wobble, let the highs react faster to tame cymbal spikes, or lift the MID band a little after compressing it to bring the vocal forward.
- Pro tip: Drag a band's dashed threshold line straight in its lane — it sets that band's THRESH, and you see right away whether the band is crossing it.
Topology & FF/FB Blend (Expert)#
- What it does: TOPOLOGY sets where the detector listens: Feedforward (to the incoming signal — tends to grab) or Feedback (to the compressor's own output — tends to smooth, the classic vintage design). FF/FB BLEND works only with Feedback and crossfades between the two: 100 % = pure feedback, lower values mix in feedforward detection. With Source = External the detector listens to the key instead, whatever the topology. Both rows are Expert-only.
- Range/units: Feedforward / Feedback (a new instance starts on Feedforward; Punch FET, Vintage Opto and FET Brickwall use Feedback). FF/FB BLEND 0 % to 100 %; default 100 %.
- In your music: The partial blend is a musical middle ground between a grabby modern compressor and a smooth vintage one.
- Pro tip: On a Feedback Style that feels a little too lazy, pull FF/FB BLEND down a touch for more grip.
Undo / Redo#
- What it does: The undo/redo arrows in the header step back and forward through your changes — up to 50 steps. A knob move, a menu pick, a drag on the display, an edit in a curve editor, a VIBE click, a whole SMART run or a whole MATCH each count as one step.
- Range/units: Up to 50 steps.
- In your music: Experiment freely — the last good setting is always one click away.
- Pro tip: Run SMART, tweak, and if you preferred SMART's version, undo back to it.
Default View (Settings)#
- What it does: Chooses which view each new plugin instance opens in. Found in the Settings panel (gear icon).
- Range/units: LAST USED (default — reopen each instance in its last-used view), SIMPLE, ADVANCED, EXPERT. Machine-wide.
- In your music: Make every new instance start on the surface you actually work from.
- Pro tip: Power users: set it to EXPERT and every new instance in every DAW opens straight into the terminal-style parameter list.
Visual Feedback & Metering#
THE_COMPRESSOR 2 is built to be watched — all metering is audio-driven, so it animates while audio plays:
- SIMPLE: a large analog VU needle — it swings left as gain reduction grows (the scale runs down to −20) and swings right when upward compression is lifting the signal.
- ADVANCED:
- A live Transfer Curve that redraws as you change Threshold, Ratio, Knee width or Knee type — including your drawn Custom knee.
- A draggable Threshold line (with a THRESH readout) and a small knee handle on the curve — drag it sideways to set the knee width.
- Scrolling input/output waveforms (about 6 seconds of history) — the input behind, the compressed output in front; where they separate, the compressor is working.
- A gain-reduction ribbon that hangs from the top of the display and reaches further down the more the compressor reduces, plus a live GR readout in dB.
- IN / OUT peak meters with peak-hold markers at the right edge.
- A 0 to −36 dB scale that extends down to −60 dB when THRESHOLD goes below −30 dB, so the threshold line always sits at its real level. It rescales when you let go, never while you drag.
- With Multiband on, the display splits into three lanes — HIGH on top, MID, LOW at the bottom — each showing that band's input behind and output in front, its own dashed threshold line and its gain change in dB. The transfer curve beside them shows the band you're editing, in that band's colour. Click a lane to edit that band.
- EXPERT: terminal-style ASCII IN / GR / OUT meters at the top (the GR bar swings left for reduction and right for upward boost), a parameter list that reflects the live state, and a status line at the bottom that reads "compressing" or "idle".
How to Use It — Real-World Workflows#
Punchy Drum Bus#
- Style → Punch FET (or Studio VCA). Detector → Peak.
- Attack short-to-medium, Release tuned to the groove; Ratio ~4:1.
- Set SC HP ~80–120 Hz so the kick doesn't drag the whole bus down.
- Restore level with Makeup, set final loudness with Output, and watch the gain-reduction ribbon grab on the hits.
Up-Front Vocals#
- Style → Vintage Opto (or a moderate-ratio soft-knee). Mix at 100 %.
- SC HP ~100 Hz to stop plosives from pumping; Weighting → Vocal to follow the presence.
- Turn on Auto Release for performances with shifting dynamics.
- Aim for 3–6 dB of reduction on the loud phrases; tweak Threshold by dragging the line on the curve.
Mix-Bus Glue#
- Style → Bus Glue, Ratio low (~2:1), and aim for just 1–3 dB of reduction.
- Bus Glue already brings Console weighting and a touch of Transformer saturation — nudge AMOUNT up for more iron, with COUPLING around 30 %.
- Run MATCH, then Bypass A/B — if the mix sounds bigger and glued at equal loudness, you're done.
Mastering#
- Style → Mastering or Tube Vari-Mu. Detector → RMS, LUFS-S or VU.
- Gentle Ratio, wide/Adaptive Knee, small Lookahead (1–3 ms). Oversampling 4x (after picking the Style).
- Keep gain reduction subtle — watch the GR readout and the transfer curve to stay honest.
Bass-Safe Mix Bus (Multiband)#
- Style → Bus Glue or Clean Modern. Open BANDS and switch on MULTIBAND.
- Set LOW X around 120 Hz and HIGH X around 4 kHz.
- Set the main Threshold for 1–3 dB of reduction, then select LOW and raise its THRESH until the lane shows the kick only nudging it; give LOW a slower RELEASE (x1.5–x2) so bass notes don't wobble.
- Watch the three lanes: the mids and highs keep their level when the kick hits.
Parallel (New York) Punch#
- Compress hard: low Threshold, high Ratio, fast Attack.
- Pull Mix down to ~30–50 % for thickness with retained dynamics.
- Trust Makeup to keep the wet level honest under the blend.
Pro Tips & Creative Techniques#
- Let SMART start, then steer. SMART nails timing, threshold, ratio, knee and makeup — your job is the last 10%.
- Audition all the Styles without losing levels: Style never touches your threshold, trims, makeup, mix or output.
- Nudge with VIBE. Not sure which knob to grab? Click WARMER, TIGHTER, PUNCHIER, OPEN or HARDER — and undo if it's not the one.
- Couple saturation to dynamics — high Coupling means clean verses, gritty choruses, automatically.
- Mid/Side for full mixes: switch STEREO to Mid/Side so a heavy center doesn't pull the stereo width down with it.
- Rescue uneven takes with Direction = Both and an Upward Floor around 18–24 dB.
- Duck like a pro: Source = External, key from the host's sidechain (kick ducks a synth/pad), and tune Release to the groove.
- Hear what it hears: open SIDE CHAIN and press SIDECHAIN LISTEN while you set HP, LP and Weighting.
- Learn by watching: keep Advanced open and study the transfer curve, waveforms and gain-reduction ribbon as you tweak — it's the fastest way to understand compression.
- Bottle your sound. When a character nails a source, save it as a user style or copy its code — you'll recall (or send) that exact personality in seconds, curves and all.
- Watch for the
*. A*on the STYLE display (Bus Glue*) means you're hearing your own variation, not the factory character — dial the value back or undo and it clears. - Open the way you like. Set a machine-wide Default View in Settings (LAST USED / SIMPLE / ADVANCED / EXPERT) so every new instance starts where you want.
Quick Start#
- Drop THE_COMPRESSOR 2 on a track (if it asks, log in with your philspeiser.com account).
- Click SMART, pick your Signal Type (e.g., Vocals/Drums/Bus/Master), set the Compression amount and an Output Target.
- Click LISTEN · 8 SEC and play the loudest part of your track.
- Listen — it's already configured. Nudge Threshold for more/less compression and set loudness with Output.
- Want a different flavour? Try a VIBE move, or switch to Advanced or Expert — your settings come with you.
Specs#
- Formats: VST3, AU (macOS), AAX (Mac + Windows). No standalone version.
- Plugin type: Effect (dynamics compressor) with external sidechain input.
- Window: 900 × 560 px, scalable with the corner zoom handle (Settings → Reset Zoom returns to 100 %).
- Views: Simple / Advanced / Expert (settings preserved across all); machine-wide Default View selector (LAST USED / SIMPLE / ADVANCED / EXPERT).
- Characters: 13 factory styles + up to 20 machine-wide user styles; every character encodes to a shareable, typo-proof text code (checksummed), with drawable custom knee and envelope curves that save and travel inside styles and codes.
- Saturation: Transformer, Tube, FET, Soft Clip, Tape; oversampling 1x / 2x / 4x / 8x.
- Multiband: 3 bands (LOW / MID / HIGH) with Linkwitz-Riley crossovers (LOW X 20 Hz–1 kHz, HIGH X 1–18 kHz; CROSSOVER: Min Phase, zero latency / Linear, 3072 samples at 48 kHz / Dynamic, no band split, zero latency); per-band threshold offset, ratio / attack / release multipliers, gain, solo and bypass. Off by default.
- Languages: tooltips in EN / DE / FR / ES / IT; built-in docs and AI assistant.
- Undo: up to 50 steps.
- Latency: 31 / 37 / 40 samples at 2x / 4x / 8x at 48 kHz; a new instance and every Style use 2x, and 1x adds none. Lookahead and the Linear crossover add more. All of it is reported to your DAW for automatic compensation.
- Older sessions: a session saved before 1.5.0 stays on the core it was mixed with and sounds as you left it. New instances use the new core, where Attack and Release do what the knobs say and every buffer size renders the same audio.
- Version: 1.5.1.



